Introducing the New SUPER TRACKER by Orbital Tracker Digital Satellite Meters a Global Leader in Satellite Meter design and manufacturing.
The SUPER TRACKER is equipped with the NEW "Fast Track" chip making it the fastest most reliable satellite meter in its class.
No more guessing with the "LOCKED" (FOUND) feature! It will positively ID the satellite you are looking for.
The Super Tracker can power the new DirecTV SWM 21V satellite LNB. No need to power the unit with a power supply or satellite receiver. Unit comes with DirecTv and Dish Network files built in.
The SUPER TRACKER is developed by Orbital Tracker for exact alignment and adjustment of satellite dishes. It is designed to be extremely easy to use. Simply select the satellite you want to find or install and the meter will try to identify that satellite only.
When finding the satellite the meter will show exact digital readouts for SNR and Quality in order to get a perfect result of the installation.
The SUPER TRACKER is microprocessor controlled, making it very reliable and accurate. Signal strength is presented on the LCD-display.
The meter searches for one satellite at a time in "Satellite Search" mode. You can also choose to view the signal in spectrum mode.
The SUPER TRACKER is very sensitive and can detect even the weakest satellite signals. The instrument can supply Voltage (13/18/21 Volt), 22 kHz and DiSEqC for direct connection to LNBs. The meter is short-circuit protected by an automatic current sensing circuit.
The SUPER TRACKER is charged via an external DC power-source or a 12 V car charger. The unit has a NI-MH removable battery pack . The unit will operate for about one hour with fully charged battery pack.
The instrument starts in the "Satellite Search" mode which makes it easy to detect the satellite desired. The instrument has a preset list of satellites which can be selected by using the Up/Down buttons. When a satellite is displayed, the meter immediately starts to search for that satellite.
The signal level will increase on the signal bar if any satellite signal is detected. If the beeper is enabled, then the pitch of the beeper will increase with signal strength. Once the instrument locks on a satellite transponder, the display is changed. Once locked on a transponder, the SNR (signal to noise ratio) bar and the Quality bar (derived from BER - bit error rate) are displayed.
Once “LOCKED” on a signal, the satellite is confirmed with the MPEG data stream using the TSID and ONID (transport stream ID and Original Network ID) for the chosen transponder.
The sequence of steps in locking are:
- “Locked” is displayed and the SNR/Quality bars are shown.
- “Found” is displayed if TSID and ONID from transponder match for the desired satellite.
If the ONID and TSID do not match, then “Wrong Satellite” is displayed alternating with the actual ONID and TSID found for this transponder. When the ONID and TSID to match are both zero, then the actual ONID and TSID are displayed.
|
|
"Satellite Search" will return to the "Satellite Search" mode. In this mode, the satellite to be used can be selected by pressing Up/Down.
|
|
|
"Satellite Scan" This function searches for a DVB-S signal every 10Mhz. It starts at the lowest frequency for the LNB type (10670MHz for Universal) and samples every 10MHz until a signal is detected.
|
"Specturm Analizer"displays a spectrum.
|
|
|
"Send DiSEqC” will enter the selection menu where the DiSEqC commands LNB1, LNB2, LNB3, LNB4 can be sent.
|
|
|
"Beeper ON/OFF" will either turn the BEEPER ON or OFF. The beeper is on by default and can be used for an audible indication when watching the display is not practical.
|
|
|
"Favorites" will allow the satellites to be used chosen from the available satellites. The satellites used in Satellite Search mode show an asterisk after the satellite name. Press “OK” to either add or remove a satellite from the Satellite Search list. Normally, the Favorites list will be a small selection of satellites from the satellite list.
|
|
|
"LNB Setup Menu" Normally the LNB Type is automatically set by the satellite selected and is shown on the display. If the LNB Setup menu is used to change the LNB type, then this LNB will be used in all further operations until power off. LNB type details are shown in Appendix C. When the LNB type is selected, then select “Save and Exit”.
|
|
|
Language: English, Spanish, French, German, Portuguese and Swedish
Auto power off: 1 min, 2 min, 5 min, 10 min, 30 min and always on.
LCD backlight: On or Off.
LCD Contrast: Lighter or Darker.
Info: Shows software version, Satlist version loaded, battery power, etc.
|
With the SUPER TRACKER you can edit your satellite list via a computer. You will need to download the STracker_List_Editor software and the US Satlist list.
When the STracker_List_Editor is loaded, it will show the last edited satellite list. Use “Import List” to load a satellite list to edit. Select the US Satlist
The SUPER TRACKER Satellite Signal Meter comes ready to use with the satellites listed below.
- Directv
DTV - 101
DTV - 110
DTV - 119
DTV - 99
DTV - 103
DTV - SWM 101 (21V) Powers LNB
DTV - SWM 119 (21V) Powers LNB
DTV Glxy 3C - 95
DTV - 72
- Dish Network
Dish 500 - 110
Dish 500 - 119
Dish 1000.2 - 110
Dish 1000.2 - 119
Dish 1000.2 - 129
Dish 1000.4W - 110
Dish 1000.4W - 119
Dish 1000.4W - 129
Dish 1000.4E - 72
Dish 1000.4E - 77
Dish Anif F3 - 118
Dish Echo 9 - 121
- Bell
Bell Nimiq 4 - 82W
Bell Nimiq 1 - 91W
- Amazonas
Amazonas - 61W
- AMC
AMC 1 - 103W
AMC 2 - 79W
AMC 3 - 87W
AMC 6 - 72W
AMC 7 - 137W
AMC 8 - 139W
AMC 9 - 83W
AMC 10 - 135W
AMC 11 - 131W
AMC 15 - 105W
AMC 21 Claro TV- 125
- Galaxy
Galaxy 12 - 133W
Galaxy 13 - 127W
Galaxy 14 - 125W
Galaxy 18 - 123W
Galaxy 19 - 97W
Galaxy 23 - 121W
Galaxy 28 - 89W
- SES
SES 1 - 101W
- SatMex
SatMex 5 - 117W
SatMex 6 - 113W
- Anik
Anif F1 - 107
Anif F3 - 118 (Dish)
- Hughes
Hugnes AMC3 - 87W
Hugnes AMC9 - 83W
Hugnes G16 - 99W
Hugnes G17 - 91W
Hugnes G18 - 123W
Hugnes G25 - 93W
Hugnes G28 - 89W
Hugnes G3C - 95W
Hugnes SM5 - 116W
Hugnes HZN1 - 127W