| | |
|
| |
| | |
|
|
|
SG-2100 DISEqC Motor For Satellite Dish
|
SG-2100
|
Detailed Description
Now you can automatically point your dish to any Satellite in Orbit with the SG2100. Motorize your Satellite Dish System with the SG2100 Motor designed for Satellites receivers with DISEqC 1.2, 1.3 and Goto X control. This unit is good for any offset Satellite Dish with a U-Bolt or Pole mounting up to 120cm aluminum or 95cm steel.
Features:
- Fits all popular dish with 42mm tube, including the Winegard 76cm Dish.
- Special design for any receiver with DiSEqC 1.2 control.
- Does Not require a receiver with built-in Positioner.
- Only one coaxial cable control
- Go to X function
- High efficiency
- Compact structure
- Ultra low noise
- Ball bearings
- Adjustable hardware limits
- Easy installation with LED Indicator
- Manual EAST / WEST button
- For any dish up to 1.2M (LESS THAN 27 LBS)
- Works with the Fortec Satar Dish and all other dishes like the Winegard, KTI, Patriot, and off brands.
- Mounts on Pole Size up to 2.5"
- Standard Shaft Size:1 5/8" (42mm) Small shaft diameter to fit most dishes.
- Optional Shaft Size: 2" (50mm) Shaft to Fit Bigger dishes with U-Bolt brackets.
|
Specification:
|
|
Model
|
SG2100
|
|
Antenna Diameter
|
120 cm Aluminum or 95 cm Steel
|
|
Azimuth Angle
|
75¢ªEAST ~ 75¢ªWEST ( 150¢ª ) Adjustable
|
|
Elevation Angle
|
10¢ª~75¢ª
|
|
Input / Output Voltage
|
13 / 18 VDC
|
|
Power Consumption
|
50 mA ( Standby mode )
200mA ( Normal)
350 mA ( Max.)
|
|
Rotation Speed
|
1.9¢ª / sec ( at 13V) ; 2.5 ¢ª/ sec ( at 18V)
|
|
Satellite Positions
|
60
|
|
Connector
|
F Type
|
|
Command Protocol
|
DiSEqC 1.2
|
|
Resynchronize Function
|
YES
|
|
Goto Position 0 Function
|
YES
|
|
Goto X Function
|
YES
|
|
Positioning Sensor
|
Hall Effect Sensor
|
|
EAST / WEST Limit
|
Adjustable Hardware and Programmable Software
|
|
Manual Button
|
EAST / WEST
|
|
Indicating LED
|
|
color
|
status
|
indication
|
|
Green
|
On
|
Power On; Standby Mode
|
|
Orange
|
Blink
|
Receiving DiSEqC 1.2 Commands/ Reset Mode
|
|
Orange
|
On
|
Error Message: Over Current / Hardware Limit
|
|
|
Tube size for antenna
|
55x160mm
|
|
Stand size
|
35~65mm
|
|
Shaft Diameter
|
1 5/8" (42mm)
|
Reset Instructions for the new SG2100 with 2 control buttons.
- Turn off your receiver to stop the power to the SG2100.
- Press and hold BOTH control buttons on the motor.
- Turn on your receiver to apply power to the motor. At this time the indicator light should alternate between green and red. Continue to hold the two control buttons until the indicator light shows a steady green. The indicator light will normally flash from green to red about 15 times.
- Your motor is now reset.
Tech Tip
Installers, carry a push-on F connector with you, the kind that slips on and off. This is a handy way to stop and re-start the power to the SG2100 when you want to do a reset.
|
|
|