DIRECTV 32-Channel Commercial Single Wire Multi-Switch SWM-32
Item Number: SWM32
Manufacturer: DIRECTV
Manufacturer Part No: SWM32R1-09
Description
Open Box
Commercial Grade SWM-32 Output Multi-Switch for DIRECTV systems.
This Kit INCLUDES:
- SWM32R1-096 Multi-switch
This is the SWM-32 or SWM32R1-09 diagram using 32 Tuners.-nbsp; The 8 way SWM splitters sold separately. Please see our other complete SWM 32 kits.
Installation Diagram-nbsp;
FEATURES:
-
The SWM32R1-09 features a Die-cast housing-nbsp; suitable for both indoor and outdoor use.(Indoor Recommended)
-
Supports six (6) LNB inputs, each triple-band stacked four ports (Ports 1 - 4) cover existing 99-deg;/101-deg;, 103-deg;/110-deg;/119-deg; satellites, plus two Flex Ports (95-ordm; sat and 72.5-ordm; sat)
-
DECA "bridge" Technology.
-
Provides 32 independent channels for supporting up to-nbsp;32 DIRECTV satellite tuners
-
Provides two outputs to serve two customer dwellings (typical)
-
Contains a built-in di-plexer for combining off-air signals with DIRECTV satellite signals onto a single home-run wire to the dwelling
- MRV multi room viewing is limited to each 8 way splitter.
Requirements for using a SWM32R1-09?
There are two basic requirements:
(1) you need a compatible dish (Slimline Dish with SL5/SL4 four output LNB) Single wire SWM lnb can not be used.
(2) you need SWM-compatible receivers.
-nbsp;SWM-compatible receivers:
H24
HR24
H25
HR35
HR20-100 through HR20-700
HR21-100 through HR21-700
HR21 Pro (all models)
HR22-100 through HR22-700
HR23-100 through HR23-700
H20-100 through H20-700
H21-100 through H21-700
H22-100 through H22-700
H23-100 through H23-700
R16-100 through R16-700
R22-100 through R22-700
R23-100 through R23-700
D12-100 through D12-700
D13-100 through D13-100
-nbsp;
What are the Flex Ports for?
The SWM has two ports labeled Flex Port 1 and Flex Port 2. These are used in DIRECTV installations that have more than one dish (such as an international dish or, in certain markets, where a separate dish is required for local channels).
What is the -ldquo;OFF-AIR-rdquo; port for?
The SWM has an input for an off-air antenna. The SWM can carry both DIRECTV satellite signal and off-air antenna signal. If you wish to use an off-air antenna, you will connect the off-air antenna directly into the SWM, and then all outputs from the SWM will carry the DIRECTV and off-air signal. You must then use a special splitter, called a diplexer, to separate the two frequencies before connecting the output to a receiver. Please be careful with your selection of diplexers-mdash;not all work properly with a SWM.
-nbsp;
What are the legacy ports and how do I (or do I have to) use them?
The SWM8 has three legacy outputs (Legacy 1, Legacy 2, Legacy 3). These three ports work like the output from a conventional 3LNB dish and allow you to use receivers that are not listed as SWM-compatible. In other words, if you want to continue using a DIRECTV TiVo or some other older receiver, you can do that. However, to use both tuners on a TiVo, you must have lines run from two of the legacy ports into Sat 1 and Sat 2 of the TiVo. A few notes about the legacy ports: (1) You cannot use any splitters to split outputs from the legacy ports. (2) We recommend that you not connect SWM-compatible equipment to the legacy ports. (3) This follows from the prior note, but the legacy ports do not transmit the signals from 2 of the 5 5LNB satellites, so only the content available from a 3LNB dish is available via the legacy ports.
-nbsp;
-nbsp;
|
|